J9九游会AG

HangZhou XinNanTian technology co., LTD
Telephone:0571-85379989 81522268
Fax:0571-85379989
Mobile Phone:13858128168
URL:novelmelayukreatif.com
Address:HangZhou east new road 22 HangGuo investigation
Product introduction

 

1. YXG08 series of letter letter stamping machine is a special equipment for internal processing of postal correspondence. Advance orders for stamps and postmarks stamped delivery.
YXG08 series had a simple letter stamp machine structure, stable and reliable, easy maintenance. The machine, the mechanical structure is divided into six parts, power, speed, for the letter, single letters separated, acceleration, too poke. YXG08 series of letter letter stamping machine mechanical design is relatively over-06 stamp machine has greatly improved, especially over the course of the stamp ink supply system made a major technological innovation, which greatly simplifies the ink refilling operation, and effective protection of the letters and poke through the machine without oil contamination, the technology has been patented. Sampling control section 89 MCU peripheral circuits and a small amount of configuration possible modular structure. Adding software to adjust the roundness and stamp stamped location features Additions stamp letter statistics. YXG08 series of letter letter stamping machine is divided into low, medium and high speed main technical indicators are as follows:

08 type (low, medium and high speed) letter stamping machine parameters:

Technical parameters: Technological parameter:

Name/speed type

Low

Speed

high speed

Volume (CM)

60×33×29

65×35×35cm

65×35×35cm

Weight (KG)

30

35

35

Poke through rate: seal/h

14400

18000

21600

Drain cover rate

≤0.5%

≤0.5%

≤0.5%

power supply

220V±10%50HZ

220V±10%50HZ

220V±10%50HZ

Noise

≤68dB(A)

≤68dB(A)

≤68dB(A)

Ambient temperature

0℃~40℃

0℃~40℃

0℃~40℃

environment humidity

60%~90%

60%~90%

60%~90%

Power

<180W

<220W

<250W

Letters allow the machine specification thickness
Allow machine correspondence nonstandard thickness
Note 1

0.1~6mm
1.5~10mm

0.1~6mm
1.5~10mm

0.1~6mm
1.5~10mm

Counting function: Cumulative stamped one hundred million, power to protect themselves.

Note 1: in line with GB / T1416 standard envelope
2. Works
Poke through the machine mechanical structure is divided into four parts, power (including transmission), for the letter, isolated and over-stamp (see Figure 1). Poke through the whole machine powered by single-phase AC motor (Eg08-bottom speed), motor speed 1400 rev / min, the two belt drive speed reducer so that the line separating belt friction is 0.852 M / S, meet the four per second excessive speed letter stamp requirement (according to the national standard number B6 envelope calculation). The power section includes a motor, motor pulley, wheel ladder, separation pulley components. For the letter portion comprises: a floating wheel for the letter for letter wheel, adjustable for letter for letter platen and photoelectric tube sample composition. When you need to put over a letter for letter stamp platen by sampling the photoelectric transfer a letter to the CPU command, CPU start the main motor operation, enter letters round pushing for a letter to reach isolated for the purpose of the letter. Separated in part by the friction of isolating and separating plate, wheel acceleration and wheel acceleration into a different friction pressure adjusting mechanism, service counter photoelectric tube sampling area constituted. Friction separation principle is the use of the friction plate and the separation zone with the separation of the friction coefficient of different letters Letters integrated single seal separation purposes. Adjust the pressure separation plate may vary friction and separation on the platen with friction, so that a single closure to achieve an effective separation of separation. Accelerate acceleration pressure roller cam action is to pull letters separated by a distance in order to ensure proper sampling count on the photoelectric reliable. In addition to sampling the signal photoelectric coincidence count outside also start poking head stepper motor. Poke poke through section contains mold, ink supply system, over stamp roller, drive a stepper motor. Only when the line speed and the moving speed of letter poke face consistent in order to achieve a qualified stamp.
3. poke through the machine requirements and methods
Users received stamp machine, open the carton and take over the stamp machine, we must first carefully read the user manual to check the correctness of spare parts, equipment checks during transport if there is damage, then remove from the bottom of the three-core machine too poke power cable. Poke through the machine should be placed on a solid and stable work surface, plug in the power (power outlet must have a good grounding wire). Turn the power switch on the right side of the machine under the panel power indicator light, over-stamp machine to enter the self-test, the display window shows 6,5,4,3,2,1 and native software version number (example: bb10), self-test poke through the end of the display unit normal low show '0'. In this case too poke entered standby state. Excluding the machine does not meet the conditions of the letter by simply finishing the bottom of the letter is slightly pulled into the station for the letter board, poke through the machine into operation, the display shows the letter passed stamp function. If you can not boot into the self-test or self-test is not the end of the show '0' or too unusual stamp indicates that poke through the machine can be used after a fault, the fault must be excluded.
http://img3.epanshi.com/2544/upload/about_us.jpg

版权所有:杭州J9九游会AG科技有限公司   
联系电话:13858128168|  联系人:石建林 地址:浙江省杭州市下城区杭州市下城区东新路杭锅群房14号